Sunday, March 30, 2014

Clews for Spin #1

If I didn't have to go to a birthday party this evening, I'd have this done today...  Aw well, maybe I'll finish it tomorrow after work...

Here are the panels in the cardboard box, along with two pairs of rings, before gluing:

Here are the panels all glued up:

I traced out the ring:

And cut it out:


Then cut some webbing.  These were leftover from some tie straps I cut down to fit the trailer and boat I have:

Then I added the two sided tape to them:

 I found it easier to do one side first:

then do the other side:


I did a dry fit and found out that I needed to trim the edges and re-position the webbing before I sewed them:

Here's what it looks liked sewed:


Here's the other set:


Then I laid the spinnaker panels down and glued the Dacron panels to them.  I found it easier to spray the Dacron panels than the spinnaker panel:


Here's the second Spinnaker panel glued to the first clew:

And it flipped over:

Here's the second one all glued up:

Here's clew #2 flipped over, note that the Spinnaker panels need trimming:

Here's what it looks like trimmed:

To glue the panels to the spinnaker I make a lift to prevent the spinnaker touching the glued panel before I was ready, it worked out quite nice!


And here's the first clew all glued!


Here's the second clew getting glued:

And it flipped over:


As per the videos, I added the double sided tape to the outer edge prior to sewing:

Same for the second clew:

And sewed the edge with a small needle and fine thread:


I decided to use the same needle and thread for the second Spinnaker panel as well.

Then it was time to leave the house and go to the party!

I'll switch to a larger needle and heavier thread before I sew the Dacron panels in and also sewing the stay tape along the edges.  I can't wait to hang this up over the pool!

The Rest of the Patches on Spinnaker #2

Here are the rest of the patches on Spin #2.  I missed taking some pictures at some of the steps!

Patch #2:





Patch #3






Patch #4






Patch #5



I ran out of thread in the bobbin at one point, and had to re-do one corner.  I was off by like only a few inches!

I am at the point where I will be making the clews next.

Saturday, March 29, 2014

1st Patch of the 2nd Spinnaker

The first patch of the second spinnaker went extremely well.

Here's what it looked like before I started:


Here's the patch material stuck to it:



Here's the finished product:


I am manually starting and backing up the needle to catch the threads in each corner, that's working out really well.  I am extremely proud of the corners, they look great!


The discoloration of the material is from where it was stored against a red panel of the spinnaker...

I am starting to experience gummy residue buildup on the needle, so that needs to be cleaned every patch or so.

I also made a mistake of accidentally sewing up part of the damaged material in one hem, I think that after I apply the double sided tape, I'll do a rough cut away of the damaged material so that it doesn't catch anymore.  I think that'll only be an issue with the larger patches though.

I think I have the machine just where I need it, it is working great!

Sunday, March 23, 2014

Patched the first spinnaker

I started to patch the spinnakers.  The smaller one is not so bad, there were only two holes, and one of them will be covered by the new clew.  It was good practice, because I needed it!

Here's hole #1

Here's hole #1 with the tape set around it:

And here it is with a cut patch.  I didn't have any red colored spin material, so I used some black instead:

That looked great!  But I didn't have the best luck sewing it:

I went over the long edges twice.  There were skipped stitches and the underside looked terrible!  Look at all those birds nests on the underside!

Yikes!  This is what it looks like trimmed out:

I expected my first patch to be sucky, but wow!  Good thing this is going in the backyard, and not on a boat!

The second patch went much better:





I was reversing on the start and end of each line to trap the thread, but note the skipped stitches again.

It looks a ton better than patch #1!

I went back and adjusted the machine again, the point was not as close to the needle as it should have been.  I did the hem and there were no dropped stitches along the whole thing!


I'm not really concerned how it looks like, as it will be covered by the edge tape later.

And like I said, no more dropped stitches!  I did notice that the needle was a bit gummed up, so I cleaned it before doing the hems.  So maybe it was a combination of a dirty needle and the final fine tuning that fixed that problem:

Towards the end, I was manually starting and reversing the stitches at the beginning and end to trap the thread.  It gave me a lot more control than the foot pedal.

I'm going to patch the larger spinnaker next, it has more and larger holes than this one.  For the two layers of spinnaker material I was using V-30 thread with a #12 needle.  Then I'll move up a needle and thread size to do the Dacron clews.  I'll try the V-90 thread and a #14 needle for that.  I have V-145 thread and #16 needles if it comes to that!  Maybe I will need that to sew the bands material.

The machine is completely lubed and working like a dream!



Friday, March 21, 2014

Finally tuned the sewing machine to sew two layers of spinnaker material

Between a week of frustration, a week long business trip and a week of being sick, I finally got the sewing machine tuned to sew two layers of spinnaker material.  The material was bunching up, no matter how I adjusted the upper and bobbin tension.

I ended up getting the following:
  • new bobbin case
  • new bobbins
  • #12 needles
  • V-30 thread
I also had to adjust the timing and shuttle rotation, as well as the rotational timing.  The manual is very detailed on how to fine tune the LSZ-1 Sailrite sewing machine.  Apparently there's a DVD that comes with every new machine that's bought, and if you call their hotline for help, they will send you links to the part of the DVD video that will address your specific problem.  If you read the instructions carefully enough, and pay attention to the diagrams, you can do it yourself.  Here's the link to their DVD video segments for tuning the sewing machine:  http://www.sailrite.com/Cap-Spring-Hook-Needle-Bar-Driver-Timing-for-Ultrafeed#.UzcQPahdXTo

Between the finer needle and thread, the new bobbin case which I could tweak the tension for the spinnaker material, and the separate bobbins where I could string up the different thread sizes, I was finally successfully able to do a hem on a scrap of spinnaker!



A medium setting on size and zigzag was perfect for the hem.


Check out the stitch on the farthest left, perfect!

Well, it is not exactly straight...  :)

Next, I will be patching the pool cover's holes and rips, in preparation for doing the clews.