Friday, April 11, 2014

Another Mistake

I should have waited to patch spinnaker #2.  Instead of patching it with discolored material from spinnaker #1, I could have used the pristine material from the panel I removed from spinnaker #2 when I re-sized it.  Aw well, live and learn.  I will not re-do those patches.  This is a pool shade cover, not a spinnaker for a boat!

Here's a picture from the dry fit of Spinnaker #2:


The ropes are there to prevent the spinnaker from bowing down to touch our heads.  When there's a breeze, the spinnaker puffs up and down, it's fun to watch.  It also makes a great sound!  As you can see, this is just not tight enough along the edges.  The removal of the panel and the re-do of the clews should do the trick!

Here are the clews cut out of the panel:

And here are the clews glued to the re-sized spinnaker.

Now I need to sew them and re-do the leather chafing.

Tuesday, April 8, 2014

Did a Dry Fit of the Spinnaker Pool Shade Covers

I put the spinnakers up to see how they fit...

Spinnaker #1 (the small one) fits the existing setup perfectly!  Three corners fit along the house, and the fourth gets pulled towards the fence corner.

Spinnaker #2 (the larger one) is too large.  The foot of the sail doesn't get pulled tight along the side of the house, and the side towards the fence doesn't pull the sail away from the house, so it rubs against the roof.  So, I have to do some modifications...

First, I'm going to have to make two new anchor points on the fence line to pull the spinnaker away from the house.  Second, I have to trim the spinnaker.  I originally kept both sail numbers thinking that would look good, and it did.  However, that made it just a bit too long along that side of the house.  So, the panel along the new, second foot needs to be trimmed off.

What I'll need to do is:

  • Remove the leather chafing protection
  • Cut the panel off with the second set of sail numbers
  • Trim the clews
  • Glue the new clews to the trimmed spinnaker
  • Sew the new clews
  • Sew new stay tapes
  • Re-sew the chafing protection
It sucks to have to re-do the clews and the foot for this spinnaker, as well as make up a new anchor system, but I think this will work out in the long run.  Having a larger pool shade cover that covers essentially the entire pool will be good to have.  

Saturday, April 5, 2014

Spinnaker # 2 - Done!

Today was a big day, I started and finished the second spinnaker.  Here's the pictures I took:

Here are the two Dacron panels:

After dry fitting and trimming, here is the panels with the webbing applied with double sided tape:

Here are the clews with the webbing sewed:

And the other sides:

And closeups:

Here I should have noticed that the spacing wasn't quite right:

Here's the panel ready to be glued to the spinnaker using my "ledge" contraption:

They're attached!

I shuffled the steps around because of where I was working, so I sewed the rings in:

I then sewed the stay tape, note the new white tape stops a bit past the panels on the side where the red stay tape is:


Ditto on the clew with the green stay tape:


I tried something new, and used some paper towel to make a template, and was able to use some scrap:

They turned out extremely well!

I can't wait to see this one hung up!








Another Mistake

I made another mistake.  Not a biggie, it is only cosmetic.

I should have caught it when I noticed in the last post that one clew had the existing tape showing and the other didn't.  What happened was that I glued the panels onto the spinnaker differently, one on one side, the other on the other side.

So, when you look at the spinnaker, you see the panel on one side but not on the other.  I'll take a picture when it is hung up and you'll see what I mean.

Wednesday, April 2, 2014

Spinnaker #1 Done?

I cannibalized an old chair of some pleather to make the chafing protector.  The problem was that I couldn't tighten the thread as tight as I wanted to, so it is pretty loosely threaded.

It'll work for now while I test it out.  I can always re-do the chafing protection later?

Here's clew #1:

 and #2:


This weekend I will sew Spinnaker #2.

Then I'll sew two spinnakers for my H16, one that'll attach to the existing tang, another to the top of the mast.

Tuesday, April 1, 2014

Sewed the Stay Tape on Spin #1

I didn't take any pictures of the process, it was pretty straight forward as per the video.

Putting the double sided tape along the new foot was a pain!  But sewing it was a snap...

I swapped out the bobbin just before I started on the new foot, so that I didn't have to stop and restart.

Here's clew #1:

And #2:

Note that I went just a bit beyond the panels then stopped on the side that had stay tape already.

The black side in clew #1 above was the panels, so you don't see the red stay tape until after the panel ends.

The red side in clew #2 above is the spinnaker, so you see the green stay tape go all the way to the ring.

I thought I had some leather in the house (by cannibalizing an old pair of shoes, gloves, a jacket etc.) but no.  So putting the finishing touch on this pool shade cover (the chafing protection) will have to wait another day.  Darn!  I thought I'd be done today!!!  Well, I wasn't going to test it until this weekend anyways...

Monday, March 31, 2014

Finished Sewing the Clews on Spin #1

I finished up sewing the new clews on Spin #1.  Here's Clew #1:

The bobbin thread finished, so I had to restart at the edge of one of the panels:

Here's Clew #2:  I sewed on the red side as the panel edges were more visible then on the black side.

Next, I sewed sinew under the ring to keep it in place and I guess to strengthen the edge:

Here's the other side.

Here's a better shot of the tools I used:

And a closeup:

Next up is the stay tape!  That'll be another day.